Motorola Ht1000 Manual Pdf

Motorola HT1000 Quick Reference Card

If it is cocked to one side, repositioning it will be necessary. On the lower right corner of the controller board is an empty female connector, which will be used to mate the controller board to the secure module. Place the secure module on the secure module pad. Once the part is off, grab it with a pair of tweezers and turn off the vacuum pump. We are not against discussion of this issue.

MOTOROLA HT QUICK REFERENCE CARD Pdf Download

Press the secure module plug into the controller board jack with enough force so that the jack and plug snap together. Begin with the highest test frequency shown. All requests will be deleted and a forum infraction issued. Customer Board Initialization When the controller board is received, it will need a serial from the defect unit.

Motorola HT1000 PDF

If the radio still does not pass the self tests, then a problem exists with the secure operations of the radio. Please do not make requests for copies of radio programming software which is sold or was sold by the manufacturer for any monetary value. Do not brush or apply any isopropyl alcohol to the frame, front cover, or back cover. Turn off the radio, check the battery connection, and turn the radio back on.

Motorola HT1000 Quick Reference Card

The benefit is you do not need multiple versions for each radio unlike Motorola. Nueb - - - - - - - - - Not Placed frequency, crystal type number, and Motorola part number. To obtain Motorola software see the Sticky in the Motorola forum. Forums New posts Search forums. The key variable is stored in volatile electronic memory, story books with pictures pdf so it can only remain in memory as long as the radio is connected to a charged battery.

Safe Handling Of Cmos Devices Upon completion of the cleaning process, use a soft, absorbent, lintless cloth to dry the area. Refer to the radio label for intrinsic safety ratings and required batteries. Each table includes model number, model number description, and the kit numbers of the transceiver board Xcvr Bd and the controller board Ctrl Bd that shipped with that particular model. The various buttons and switches are programmable to do dofferent things so it owul djust be an overall guide.

If the component part number is not known, the order should include the number of the chassis or kit of which it is a part, and sufficient description of the desired component to identify it. The various other vendors often permit their dealers to sell the software online i. It's now worn out and continues to be the same recycled rants.

Getting StartedMotorola ht manual

Page To actually use the secure option, Secure must be enabled on the Channels channels for which it is desired. One key variable can be stored in the module at a time. This prying action forces the thin inner plastic wall toward the base of the radio, which releases the two chassis base tabs. Status Not open for further replies.

Motorola HT PDF

Typically each series or individual radio requires its own software package. Reassembly Ensure that the board slides under the tabs. Media New media Search media. Lift the freed leg of the retainer bracket and use it to pull the remaining two legs of the bracket out and away from their respective slots in the front cover housing. Turn the control top such that the grey switch housing cover is facing up.

Page West Sunrise Boulevard Ft. We do not want any hurt feelings when your vague post is mistaken for a free request.

Check to make sure that the O-ring is in place, and slide the chassis control top first into the front cover assembly. The conventional package is more reasonable though is still several hundred dollars.

The smaller size solder will melt faster and require less heat being applied to the circuit. Patent and Trademark Office. Pry the bottom of the chassis free from the cover by pushing the separation tool down and rotating the handle of the separation tool over and behind the base of the radio. More Electrical Parts List. Five retaining clips hold the switch housing cover to the switch housing.

Disconnect the front cover display flex from the connector on the chassis. What do you guys need to know about the radio?

Page With the front shield raised, observe the controller board which takes up the bottom third of the radio. Check to ensure that the orange emergency button seal slides into position freely. You just need to do it in the right place. Near the three larger slots on the other side of the board, use finger pressure to push and press that side of the board down until it snaps into place under the three large retaining tabs. Alternatively, you can get the Real Deal pretty cheap, if you shop around a bit.

This is a large and very visible forum. Please use Google or some other search engine to find a dealer that sells the software. Replacement Parts Ordering This applies to all components, kits, and chassis. If you are having trouble legally obtaining software please state so.